[. . . ] ContiSys OBD Instruction Manual 08/2009 - EN(2. 0) 08/2009 - EN(2. 0) 2 Contents Introduction Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Display screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] This indicates that the text can be scrolled using the and keys to view the rest of the description. 38 FastCheck To view the next DTC (if more than 1 was found), scroll to the end of the text and press the key. To return to the menu, scroll to the end of the text and press the key. Clear DTCs Diagnostic trouble codes can be cleared using the 'Clear DTCs' option. Verify that the code(s) have been cleared by selecting 'Read DTCs'. Note: Reading DTC(s) without first starting the engine will only confirm that the stored DTC(s) have been cleared. Faults may still be present in the system causing a DTC to be stored next time the engine is started. BMW vehicles Note: To switch the ignition ON for vehicles fitted with a start/stop button, insert the remote key-fob fully into the ignition slot then press the start/stop button once (without any foot pedals depressed). SAS (Steering Angle Sensor) Calibration The steering angle sensor can be calibrated using the `SAS Calibration' option. The on screen instructions must be performed to ensure the calibration process is correctly completed. Note: The steering angle sensor should be calibrated after performing the wheel alignment or suspension adjustments. 39 FastCheck FastCheck Service Connection Using the Vehicle Application List on the CD-ROM, identify the required interface cable for the vehicle system to be tested. Note: If the vehicle being tested is a BMW fitted with both a 20 pin connector and an EOBD (J1962) connector, you must only use the 20 pin connector. Note: If the vehicle being tested is a Mercedes fitted with both a 38 pin connector and an EOBD (J1962) connector, you must only use the 38 pin connector. E D C B F G H I J K 4 3 5 6 7 8 9 A L 2 1 12 10 11 CON0017 If using the EOBD (J1962) pin-switchable cable (A2C59512073), ensure the settings on the switch box correspond to the settings listed for the vehicle and system being tested. WARNING: Incorrect settings on the switch box may cause irreparable damage to the vehicle's electrical system. Connect the service tool to the required vehicle connector, refer to `Diagnostic connector locations', page 57, for further information. Once connected, the service tool will perform an internal self test and then the screen will display the version of the current software before displaying the main menu. MAIN MENU 1. EOBD FastCheck FastCheck FastCheck FastCheck FastCheck FastCheck User Menu ABS Airbag Climate EPB SAS Service Use the and keys to select the 'FastCheck Service' application and press to confirm the selection. keys to select the vehicle manufacturer and press to confirm Dependent upon the vehicle manufacturer and model different menu options will then be available. Alfa Romeo vehicles (UK only) For Alfa Romeo vehicles with the Mannesman Dashboard (147 and GT) there is a problem with the Dashboard which causes the 'Number of miles to Service' value to be set to zero when a Service Reset is performed using the service tool. When the Service Reset is performed the Dashboard stores the current mileage (or kilometre) value, read from the Odometer, in order to calculate when the next service is required. However, when the Odometer is shown in miles the calculation for the distance to the next service fails. This results in distance to the next service being displayed as zero and the Service Reset fails to be completed. To reset the Service Interval the following procedure must be performed: 1. [. . . ] To reset this counter, press and hold button B until 5 dashes appear on the display. To reset this counter, press and hold button B until 5 dashes appear on the display. To reset this counter, press and hold button B until 5 dashes appear on the display. When "IN 00" is displayed, turn the ignition switch to the OFF position. 110 Appendix D: Manual service reset Volvo Volvo 240 (1986 - 1989) 7 0 SERVICE 0 km/h MPH 120 PARKING BRAKE CON0038 Reach behind the instrument panel and push the lever located between the tachometer and the speedometer. [. . . ]